Full body walkthrough metal detectors-max 90 detection zone

full body metal detectors-max 90 detection zone

Walk Through Metal Detector 90 zone   USER MANUAL

 Contents Table

 

1. Chapterⅰ: Summary

   • Definition
   • Installation, operation and attentions
   • The electronic control unit
   • Door panels
   • Power Adapter
     

2. Chapterⅱ:

    Installation

   • Installationattentions

• Choose the installing location
• Designthe checkpoint
  • Tips for install more than one piecesWTMD side by side
  • Assemble

 

3. Chapter

    ⅲ: boot and screen display and procedures set

   • Power on the WTMD and boot
   • Screen Menu and program setting
   • Multi-zone display
   • Power saving mode and standby mode
     

4. Chapter

    ⅳ: maintenance, maintenance , service

   • Maintenance& after service
   • Routine maintenance
   • Maintenance attentions
   • Storage conditions , storage period andattentions
   • After service

1. Chapterⅰ: Summary

 

Thank you for choosing this WTMD. The following are installation and daily operating instructions for our WTMD.  In addition to these instructions, this should be in accordance with local laws and regulations and government requirements.

 

Before installing or using this WTMD, please read and learn this manual

This manual includes information required by the user about the structure, installation and operation. Follow the proper operation and maintenance procedures to keep the WTMD in reliable status.

It is a multi-zone Walk Through Metal Detector (WTMD).

This WTMD in part by the electronic control unit and two detectors. The electronic control unit includes a variable magnetic field generators, receivers, signal processors and process controllers; the detector contains two transmitting and receiving antennas, which are pre-installed on the inner side of the two door panels. Among the above parts are connected via cables (electronic control unit out lead two pcs of cables, these cables connect control unit to the two detectors).

WTMD outframe is consists of two door panels and a main box. One side of the door panels has power connector at the bottom, while the other side has not. Main box are fixed with two door panels to shape the door arch. Electronic control unit are fixed inside the main box. Inside the two door plates, LED light bars are installed from top to bottom.

• Definition

The following are definition for some special name mentioned in this manual.

• Sensitivity – isused to define parameters for alarm metal object size. Raise the sensitivity; smaller metal objects can be detected.
• Discriminating – the ability for WTMD todistinguish metals (especial metal weapon) and other articles. WTMD alarm rate can indicate the ability to WTMD discriminating. It is affected by many factors, such as sensitivity levels, passengers’ body shape, season (temperature) and so on.
• Useless alarm – alarm caused bycarrying harmless metal objects  
• False alarm – alarm caused by the reasons other than by a metal object (such as electronic interference). ForWTMD, the alarm caused by the metal objects (useful or useless) is not false alarms.
• Alarm rates – alarm times(caused by metal objects) / Passengers *100%. Alarm rate is affected by WTMD discriminating ability. If discriminating ability is poor, for example: there are many alarms caused by harmless metal objects, the alarm rate will be Alarm rates don’t include alarms caused by electronic interference and other reasons.
• Pass rate – at a given time, maximum number of passengers allowed. Pass rateshows the WTMD recover ability after the former detect. In practice, due to the check process and the maximum walk speed and other factors, while the maximum rate is only for theoretical.
• Speed response –the abilityfor WTMD to maintain the same level of sensitivity, while inspecting passenger walk at different speed.   
• Calibration –in order to achieve optimum performance; set the parameter values ​​for WTMD at the installation site.
• Side by sideuse – if two or more WTMD work side by side, their electromagnetic field will affect each other. Choose different frequency to reduce the interference.
• Operating Frequency– frequency generated by WTMD electromagnetic field.  During the calibration at site, choose different frequencies at the lowest interference level. WTMDs can be installed side by side
  • Installation, operation and attentions

Please read the follow introduction before installation
Supplier is not response for damages caused by disobedience of follow instruction.

• Read this manual carefully before installation and operation. Take away of this manual for future reference.
• Manual has a detailed description of the installation, debugging method. Supplieris not responsible for the damage caused by human.
• Sensitivity and detection methodare selected by the end user. The user should do commissioning work under supervision by professional and technical personnel for debugging.
• Whenever the WTMD has problem, the user must keep the WTMD in safe place to avoid accidence, and requests for assistance.

The following problems are considered:

• A visual signal display of WTMD isnot normal.
• The WTMD does not work
• WTMD was stored in unsatisfactory conditionfor a long time.
• WTMD suffered high pressureduring 
• Liquid has been spilled inside the WTMD

• Carefully select the installation site. Do not installthe WTMD in a location near a heat source. Also, avoid do not install in a location, where could have vibration, dust, moisture, high or low temperature place.
• Installation must be performed by specially trained the person. Keep enough space to do the installation job, to avoid hurting Keep the site in tidiness.
• Install the WTMD away from the location, where could emit electromagnetic interference,such as a location with transformer or
• For best performance, the WTMD should be fixed on the ground. All connection between WTMD andpower supply or other external line must be properly secured and protected in order to avoid unexpected accidents and injuries to passengers.
• Before power equipment,make sure the power supply voltage is accordance to the voltage indicated on the WTMD.  Different voltage may cause Only after the completion of all required connections, user can connect WTMD to electricity power.
• Power line connect to the WTMD, must have switchor any other component which can cut the power in case of accident.
• If the WTMD is powered through an external autotransformer to normal voltage,ensure that the autotransformer common terminal is connected to the power supply circuit hub. Socket must be grounded. Disconnect the ground without permission is strictly If the WTMDs are not grounded, in exceptional circumstances may cause damage.
• Disconnect the power supply with a closing pull of the plug, not thewire.
• Standard configuration of the power adapter for non- waterproof type:Keep it in ventilated and dry place. Once get wet, there is the danger of electric shock and damage to WTMD.
• Electronics partsof WTMD may cause a fire.  Do not install at flammable explosive In case of fire, don’t use water or foam extinguisher to the power on WTMD.
• In case; thunderstorms, disconnect the power.
• Do not use WTMD in an explosive Avoid contact with flammable substances and explosive.
• Maintenance the WTMD in periodic (Referto “Maintenance” chapter). Do not use water, detergents or chemicals for cleaning. Use a damp, smooth cloth.
• Disconnect the WTMD power before maintenance, cleaning or moving.
• Please read the “Maintenance” chapter. No matter what kind of problems encountered, only the factory qualified engineer is permitted to do
• Any necessary replacement partsmust be factory original.
• Aviod maintance WTMD while power on. If have to, the engineer must be professional and fully understand the
• Recommendations about the battery inside the WTMD:
• When replacing batteries,use the factory supplied battery.
• Do not throw used batteries in normal Throw to the use batterycollection facility, according to local regulations; or return to supplier.
• When handling the problem of WTMD, remove the batteryfrom WTMD in advance.  Supplier is not responsible for damage caused by incorrect using of batteries.

 MARKS

 Only professional engineer are allowed to maintain components with follow marks.

        

 

• Before opening the package, please read carefully the following introduction. If notfollow the installation procedure specification, supplier will not responsiblefor any problems that may occur.
  • The electronic control unit

 

1. Sticker
2. LCD menu
3. Keyboards
4. Connector to door panel

• Door panels
  Use special synthetic material.

With a specially designed transmit and receive coil to ensure uniform magnetic field distribution and high sensitivity of detection

 

• Power Adapter  
  Input power: AC100 to 240V

Output power: 15VDC, 5A
Adapter size (L*W*H): 114*50*30mm
Cable length: 2.5 meter
Weight: 0.5 kg

 

2. Chapterⅱ:

    Installation
   

   • Installationattentions
     • Choose the installing location
       Excludeor deduce the negative effects, when install WTMD. This is to ensure that WMTD perform the best and fast.
       
   • Still large metal objects should be at least 30 cm away from WTMD. The farer the better.  When only 30cm away, there is few affectto the sensitivity, but WTMD could be easier affected by vibration. 
   • The installation ground should be flat, with strong support, to prevent vibration. Especially when there is unstablemetal articles under the WTMD, the vibration will course unnecessary alarm, when passenger pass the WTMD.
     
     
   • The moving large metal objects should be5m to 2 m away from the WTMD, to avoid an unnecessary alarm. The distance is decided according to the size of the metal objects.
     
   • Electronic interference sourcesshould be far away from the WTMD. The minimum distance is 5m to 4 m. However, the actual distance is decided by the environment. You can move the interference sources or WTMD, until you find the best position. Interference source can be the electronic control panel, radio, computer, image display, high power motor, transformer, electricity wire, silicon tube control circuit, the flashing fluorescent tube, welding equipment and so on.
     
   • Connect the power cord to circuit, which is not connecting to high power consumptiondevice (for example high power motor).  

 

• Design the checkpoint
  

In order to have the best traffic, please design the checkpoint before installation. Besides considering mechanical and electronic interference (please refer to: 2.1.1), effective safety inspection is also be appropriate. The efficiency of the checkpoint is greatly affected by the following factors:

• Keep the passengers in queue. Make sure people pass one by one.
• Check the alarm passenger in other place, where will not affect the work of WTMD.   
• Check the bag by X Ray or manually. Don’t let the passenger with bag pass WTMD.l
• If no need to check the bag, please store the back in locker before accept inspection.

 

• Tips for install more than one piecesWTMD side by side.

• When more than two WTMD are installed side by side (distanceno more than 10m), program different Channel for each device.
• When more than two WTMD are installed side by side, distance between each WTMD should be at least 0.5 meter (Actualdistance is depends on the sensitivity level. Farer is sensitivity high)

 MD is short for Walk Through Metal Detector.  

 

• Assemble
  

• When opened the package, put out the parts Take away all the tools (screw, wrench, etc.)
  
• Choose reasonable installation location
  
• Make sure components are fixed well. When stand the WTMD, check whether the two doors panels are vertical to the groundand the distance between the upper and bottom for each door panel is equal.
  
• Make sure the WTMD is working in stable condition. There should be no big metal object moving or vibrating nearby.
  
• Prohibit to dill any hole or thwack screwsin the door panel.
  
• Power:Before power on the WTMD, be sure to check the local power supply voltage matches the WTMD input voltage.
  
  

Warning:

Connect to incorrect power supply, may cause the damage to the WTMD.

Avoid moving metal articles wit in distance of 70cm.

Avoid power cable within distance of 50cm.

Installation:

1. Connect the door panels tomain box by screws, use special wrench to tighten.
2. Connect the two cablesfrom electronic control unit to each door. The two cables looks same, please connect left cable to left door panel, right cable to right door panel.

 

 

 

 

 

 

• Chapterⅲ: Boot and screen display and procedures set
  
  • Power on the WTMD and boot
    
    The power interface part see the attached pictures below. After turning on the power supply, security will send out the alarm sound of a few seconds, and the following content is displayed on LCD screen
    

Operation		Introduction
		Power plug
		1. Factory name 2. Brand 3. Model number
		Start automatic diagnosis 1. Diagnosis the WTMD 2. Scan the current environment 3. Automatically Calibration to adapt environment.

 

 

 

 

 

• Screen Menu and program setting

 

Operation interface		Introduction
		There are five buttons on the operation panel.   ESC: return to the upper menu or exit the program Settings : feature shift and increase parameter : feature shift and reduce parameter ENTER: save data or enter to next interface POWER: turn on/off
		Normal working status information: 1. Serial number: SN: 000000 2. Number of passenger 3. Number of alarm 4. Calendar and time 5. Number of detect zones 6. Current working Channel 7. Press “ESC” key for long, to clear the current information.
		Input password before programming （Original password：100000）

 

 

 

Operation interface		Introduction
		To program the WTMD ： 1. Press ENTER to select 2. Press    or   to shift 3. Press ENTER to enter to next menu
		Sensitivity setting： 1.  Overall sensitivity: when overall sensitivity level change, all zones sensitivity change. 2. Zone sensitivity: adjust different sensitivity for each zone separately.
		Overall sensitivity： 1. Change overall sensitivity level to change sensitivity of all the detect zones. 2. Overall sensitivity level range from 1 to 300, the bigger number, the higher sensitivity. 3. Progress bar show the parameters 4. Press ENTER to save the sensitivity level

 

 

 

 

 

 

Operation interface		Introduction
		Zone Sensitivity: 1. Adjust each zone separately 2. Sensitivity level range from 1 to 300, the bigger number, the higher sensitivity.
		Alarm Setting: 1. Audio Alarm lasts: the audio alarm time range from 1s to 9s. 2. LED alarm lasts: LED light alarm last from 1s to 9s. 3.  Alarm volume range from level 1 to 20. 4. Alarm tones: Change from 1 to F (16 different tones for choosing)
		Zone Setting: 1. Program the quantity of detect zone (Different price, you will have different zone choice) 2. Press ENTER to select 3. Press    or   to shift 4. Press ENTER to save

 

 

 

Operation interface		Introduction
		Date and Time setting 1. Sett the WTMD at accurate date and time. Wrong setting will affect the working. 2. Press ENTER to select 3. Press    or   to shift 4. Press ENTER to save
		System Language Chinese and English ready Other language need further upgrade
		System setting: 1. Working Channel: total 100 different channels to choose, to avoid interference for WTMD side by side. 2. Detect speed:  change from 1 to 100 person per minute 3. Power condition: ON/OFF ON: Once power on, WTMD automatic start to boot OFF: When power on, WTMD standby ,need press POWER button to start

 

 

Operation interface		Introduction
		Display setting: 1. Display mode: Indoor/outdoor 2. LCD light: 1% to 100% adjustable 3. Press ENTER to select 4. Press    or   to shift 5. Press ENTER to save
		Problem Diagnosis 1. Left/right door panel: select to diagnosis the door panel. Once problem, system will show you error code. 2. Audio Alarm: select to diagnosis, audio alarm will on for test purpose. 3. LED: select to diagnosis, LED alarm light will on for test purpose.
		Application spot There are 33 different choices. The user can choose the accurate spot and then adjust sensitivity to get the best match setting.

 

 

Operation interface		Introduction
		Records 1. Show alarm records, system working hours, passenger amount. 2.  Input start and end time to find record 3. Press ENTER to select 4. Press    or   to shift 5. Press ENTER to save
		Password: 1. Amend password ； 2. Press ENTER to select 3. Press    or   to choose number. 4. Press ENTER to save

 

• Multi-zone display

WTMD can give LED light alarm to locate the metal threats, at the corresponding height. When alarm, one or more sets of LED lights will be on, indicating the position of metal objects.

In the case of no alarm, two power lights on top of each door panel will keep flashing.

 

 

 

 

 

There are seven choices of alarm zone: single zone, 1 zones, 8 zones, 15 zones, 16 zones, 24 zones, 30 zones, 45 zones. The user can program in menu Zone Setting. Sensitivity level of each zone can be adjusted separately

 

LED alarm for 8 Zone setting

LED alarm for 16 Zone setting

LED alarm for 45 Zone setting

 

• Power saving mode and standby mode

WTMD will automatically program to Power saving mode, if device not working in 5 minutes.

Once passengers pass, WTMD will automatically back to normal working condition.  

 

• Chapterⅳ: maintenance, maintenance, service
  • Maintenance& after service

WTMD is high-tech electrical device. The operator is requested not only to understand the   technical performance, structural principle and operating procedures, but also good at doing the daily maintenance and maintenance work. This is to guaranty working efficiency and extend device life, and to ensure safety.

 

• Routine maintenance

To ensure the good working condition, WTMD should be checked and adjusted regularly.

Maintenance job must be done by qualified people.

Cut the electricity, in case of checking hardware.

Daily maintenance work:

• The device should be installed in the ventilation,dust clear, dry environment, avoid high temperature, high humidity and direct sunlight.
• Clean the dust inside device.
• Tighten the loosen components or wiring plug, if any.
• If any parts damaged, please find out the reason and solve the trouble first, and then replace it. After replacement you need to adjustsensitivity again.
• Don’t leave other object inside WTMD. This may course electricity accident.
• Maintenance attentions

• Don’t leave other object or water inside WTMD
• Cut the electricity and then check the device. If have to be on power, please know the risk well, and operator should be professional qualified.
• Before repair, prevent electrostatic damageto the precision electronics.
• Before power on, make sure that all cables are connecting
  • Storage conditions , storage period andattentions

Device should be stored in a clean and dry place, excessive heat and moisture can damage the system components. If the device will not use for a long time, it should be stored in the original packaging box.

• The storage conditions of the equipment

In the transport or storage packing condition, the device must be set in follow condition

Storage temperature: – 20 ~ + 60 ℃ (condensate)

Humidity: 20% ~ 95%

The storage time cannot exceed 15 weeks.

• If need long-term storage, device should have good storage conditions.The warehouse should be clean and dry, well ventilated, there shall not be corrosive gas, the relative humidity is not more than 80%, and the equipment should be in the packaging box.

 

• After service

 

Thank you for choosing our WTMD. We give one year free after service to buyers. While we will be responsible or device in follow condition:

• Device parts, trade mark or serial number is missing.
• Device is damaged because of incorrect operation.
• Device is damaged by irresistible force.
• Device is dispatched by unqualified people.
• Device is connectingwith other products, which is not allowed.